Users questions 

Where are the fuses on a 2005 Ford F150?

Joe Ford

Where are the fuses on a 2005 Ford F150?

Fuse box location The fuse panel is located under the right-hand side of the instrument panel behind the cover. Remove the trim panel and fuse box cover to access the fuses.

Where are fuses in Ford F150?

Passenger compartment fuse panel Ford F-150. The fuse panel is located under the right-hand side of the instrument panel. To remove the trim panel for access to the fuse box, pull the panel toward you and swing it out away from the side and remove it.

Where is the fuse box 2006 F150?

It is in the passenger side kick panel. You will see the passenger side kick is a lot thicker than the driver’s side. Finger notch to the front of the truck, pull this in a swinging motion to the rear of the truck ( like opening a door ).

Where is the fuse box on 2007 F150?

This 2007 Ford F150 Fuse Diagram shows a central junction box located in the Passenger Compartment Fuse Panel located under the dash and a battery Junction Box under the hood.

What are the symptoms of a bad fuel relay?

How to tell if fuel pump relay is bad (6 Signs)

  • Check Engine Light (CEL) Illuminated. In most cases, the primary symptom is a check engine light.
  • High Mileage.
  • Long Starting Time.
  • Engine Performance Issues – Stalling, Idling, Acceleration, Not Starting.
  • Car dies while driving.
  • Silent Fuel Pump Noise.

Is it OK to bypass fuel pump relay?

Jumpering or bypassing the fuel pump relay puts a constant +12VDC to the fuel pump. Basically you have voltage directly from the battery to the fuel pump, even with the engine turned off. You could use a jumper assembly with a toggle switch to manually turn on and turn off the fuel pump.

Does fuel pump need relay?

It depends on how long the wire run is, how thick the wire is, how much current the pump draws, and what other types of controls you want on the pump circuit. Low current pump, short heavy wire, no funky control requirements means you can go without a relay.

Can you switch relays?

Determining different relays Both types can fail and should not be interchanged. To clarify, swapping relays is not the only item that can cause voltage spikes, but it is a shortcut practice that can lead to avoidable damage.

How do you tell if a relay is bad with a multimeter?

Use a digital multimeter (DMM) to test the resistance between each pole of the relay and the corresponding NC and NO contacts for that pole. All NC contacts should read 0 ohms to the corresponding pole. All NO contacts should read infinite resistance to the corresponding pole. Energize the relay.

Can I use a 5 pin relay instead of a 4 pin?

Some 5 pin relays are SPDT (switch between the two pins) and some are DPST (like the main relay- connect 2 pins at the same time.) If you want to use a 5 pin in place of a 4 pin, you shouldn’t have to remove the pin. The socket should be the same, but the center pin won’t have a contact in it.

What does a 5 pin relay do?

5 pin relays provide 2 pins (85 & 86) to control the coil and 3 pins (30, 87 & 87A) which switch power between two circuits. They have both normally open and normally closed connection pins. When the coil is activated, power will be switched from the normally closed pin to the normally open pin.

Do you put a fuse before or after a relay?

It could be conceivable that the relay could get an internal fault and short the live feed to ground. If you put the fuse after the relay, then that internal short would mean that the live wire from the relay to the battery is not protected. It could then melt and cause a potential fire risk.

Can I use a lower amp relay?

It depends on the application. You will find that the relay switches much more quickly when powered at the rated voltage. This results in clean switching with minimum arcing and contact bounce. For a low current application it may be fine.

How many amps can a 12V relay handle?

6.25Amps

How do you know what Relay to use?

An easy way to determine the limit of a relay is to multiply the rated Volts times the rated Amps. This will give you the total watts a relay can switch. Every relay will have two ratings: AC and DC. You should determine the AC watts and the DC watts, and never exceed these ratings.