What size hole do you drill for a 3/16 Rivet?
What size hole do you drill for a 3/16 Rivet?
Table 1.
| Nom. Rivet Dia. | Hole Size | Drill No. |
|---|---|---|
| 3/32 | 0.097 – 0.100 | #41 |
| 1/8 | 0.129 – 0.133 | #30 |
| 5/32 | 0.160 – 0.164 | #20 |
| 3/16 | 0.192 – 0.196 | #11 |
What size is #6 drill bit?
Drill Bit Sizes For Pre-Drilling For Screws Most Commonly Used Sizes In Bold
| Screw Size | Pilot hole size for hardwoods* | Pilot hole size for softwood** |
|---|---|---|
| #4 | 1/16″ | 3/64″ |
| #5 | 5/64″ | 1/16″ |
| #6 | 3/32″ | 5/64″ |
| #7 | 3/32″ | 5/64″ |
What size drill bit should I use for a 5/16 lag bolt?
Lag Bolt Dimensions
| Lag Bolt Pilot Hole Sizes | ||
|---|---|---|
| Bolt Size | Pilot Hole Size | |
| 5/16 | 5/16 | 13/64 |
| 3/8 | 3/8 | 1/4 |
| 7/16† | 7/16 | 19/64 |
What is equivalent to a 5mm drill bit?
Standard metric drill bit sizes
| Drill size | Diameter (in) |
|---|---|
| 4.9 mm | 0.1929 |
| 5 mm | 0.1969 |
| 5.1 mm | 0 |
What drill bit is closest to 5 32?
What size is 5 32 drill bit?
| Drill Bit Hole Diameters | ||
|---|---|---|
| Metric Size | Fractional Size | |
| .8 mm | .0315 | 1/8 |
| .9 mm | .0354 | 9/64 |
| 1 mm | .0394 | 5/32 |
What size drill bit do you use for 1/4 20 tap?
A hole that is too large will result in a loose bolt, which will not have 100 percent of its structural strength when fully tightened. For a 1/4-20 bolt, the optimal drill bit size is #7 or 13/64th.
What size hole do I drill for a 1/4 bolt?
| Screw Size-TPI | Recommended Hole Diameter | Drill Bit Size |
|---|---|---|
| 1/4-20 | 0.2280″ | #1 |
| 5/16-18 | 0.2900″ | L |
| 3/8-16 | 0.3580″ | T |
| 1/2-13 | 0.4531″ | 29/64″ |
What size drill bit do I need for a 1/2 bolt?
Use the same size drill bit as the diameter of the bolt. If you are using a 1/2″ diameter bolt use a 1/2″ drill bit.
What size drill bit do you use for a 1/4 pipe tap?
| Tap size | Threads per inch | Drill size w/ taper pipe reamer |
|---|---|---|
| 1/8 | 27 | 21/64 |
| 1/4 | 18 | 27/64 |
| 3/8 | 18 | 9/16 |
| 1/2 | 14 | 11/16 |
What size drill bit do I need for a 6 32 tap?
US Tap and Drill Bit Size Table
| Tap | Fractional Drill Bit | Number Drill Bit |
|---|---|---|
| #5-40 | – | 38 |
| #6-32 | 7/64″ | 35 |
| #8-32 | – | 29 |
| #10-24 | 5/32″ | 25 |
What is a taper pipe reamer?
Taper Pipe Reamers are multi-fluted, end cutting tools used to resize and clean up previously formed holes prior to tapping. Taper is 3/4″ per foot.
What is a Npsf thread?
NPSF (Dryseal) straight pipe working gages are used to check size of the straight internal threads intended for assembly with NPTF external threads. A GO and NO GO gage are used to insure the threaded part is within acceptable tolerance. NPSM straight thread gages are designed for free fitting mechanical joints.
What size is SAE 16?
SAE 45° Flare (SAE J512)
| Inch size | Dash size | Male Thread O.D. (in) |
|---|---|---|
| 5⁄8 | -10 | 7⁄8 |
| 3⁄4 | -12 | 11⁄16 |
| 7⁄8 | -14 | 1 1⁄4 |
| 1 | -16 | 1 3⁄8 |
Are JIC and UNF the same?
The only effective difference is that JIC (also known as SAE 37 degree) has a conical seating face (37 degree or 74 degree total angle) and UNF Straight has a flat seat – sealing being effected by use of a washer. Male JIC fittings have a convex cone, female fittings a concave cone.
ARE AN fittings 37 degree?
AN fittings are a flare fitting, using 37° flared tubing to form a metal-metal seal. They are similar to other 37° flared fittings, such as JIC, which is their industrial variant.
Do JIC fittings need Teflon tape?
Registered User. You don’t need or should use any teflon tape or pipe dope on hydraulic fittings. Neither are designed for those kinds of pressures and using them could create a less then perfect mating between connection surfaces causing more harm than good.