What is the meaning of choke off?
What is the meaning of choke off?
transitive verb. : to bring to a stop or to an end as if by choking.
WHAT ARE ON OFF symbols?
The power switch is a rocker switch and it has two symbols on the face: “O” and “—“. They are the International symbols for power “On” and power “Off”. “O” means the power is OFF and “–“means the power is ON.
Where did the power button symbol come from?
The power button resembles a small circle with a vertical line. The universal symbol is believed to have originated when the term ‘On and Off’ was replaced by numbers 1 and 0. The numbers were derived from the binary system, in which 1 stands for power and 0 indicates power off.
What does on off on mean?
ON-OFF means. if the toggle/lever is in the ON positions the switch is latched ON. if the toggle/lever is in the OFF positions the switch is latched OFF.
What does off with you mean?
get off with (someone) idiom. : to have sex with (someone) : to begin a sexual relationship with (someone)
What is a buy off?
transitive verb. 1 : to induce to refrain (as from prosecution) by a payment or other consideration. 2 : to free (as from military service) by payment.
What is on or off?
It comes from the binary system (1 or | means on). O – IEC 5008, the power off (circle) symbol on a button or toggle, indicates that using the control will disconnect power to the device. It comes from the binary system (0 means off).
What does 0 and 1 mean on a switch?
so 0 is like zero current is going through, and 1 means a current of 1 is going through, therefore that means On.
How many seconds do you need to hold down the power button to shut off the computer?
Do not perform a hard reboot regularly. Press and hold the power button on the front of the computer for approximately 5 seconds.
Where is the power switch on a motherboard?
You will need to locate the power switch pins. They are located at the bottom of the board.
What is GND on motherboard?
The System panel cables, as shown in the picture are two wire cables that are color-coded to help identify where they connect to the motherboard system panel connector. The black or white wire is the GND (ground) wire and the colored wire is the powered wire.
Is HDD LED necessary?
You don’t need them. I ripped my led wires as soon as I got my PC parts. It’s a standard that has been around over 20 years and I’ve never seen a motherboard that wont accept a normal 2 pin led connector.
Why is HDD light always on?
Hard Drive Light Stays On – Delete Computer History. When your hard drive light stays on, its a indication that your hard drive is working. At any rate, if the hard drive is flashing non stop, it means there is a problem.
What does HDD LED mean?
hard drive activity light
Which side of HDD LED is positive?
red
How can you tell if a computer wire is positive or negative?
Champion. The color is always positive while white/black is always ground/negative. This is universal in most electronics except in home electrical where green is almost always used as ground. But red/green is positive and white/black is negative in your case.
Is Ground positive or negative motherboard?
For example, black should always be ground/negative. In typical wiring, you have red/white = positive, black = ground/negative, green/bare copper = ground. If there is no green, then black is ground. This is a basic convention that any electrician should follow.
What is F panel on motherboard?
The front panel header is where the connectors of hard disk drive activity lights, case speaker, reset button, power on/off button, computer power on light, and key lock, are connected to make them function smoothly. Connecting the front panel would no longer be the headache of installing motherboard anymore.
What does CI mean on a motherboard?
CI: Chassis Intrusion Header.
What is JCOM1 on motherboard?
JCOM1 is an old school serial interface header. you plug a two row DB9 serial plug in there so you can ave a serial port. pre ps2 mouse interface.
What is the use of mounting hole in mounting the motherboard?
Motherboard mounting screw hole Each motherboard has several holes to help hold the motherboard securely in place. Often the screw holes can be easily identified because they’ll have metal surrounding each hole. Some earlier motherboards may also have holes without metal surrounding the hole.
Do you need front panel connectors?
You need both JPWR1, the big 20+4 connector on the edge of the motherboard and the JPWR 2 ,the four pin CPU power connector plugged in for the system to work properly.