How wide should a hole be for a 6×6 post?
How wide should a hole be for a 6×6 post?
The depth of your hole should be about 1/4 of the height of your post. For a 6×6 post, the diameter of the holes should be about 12 inches square. As a rule the width of your post hole should never be less than 10 inches.
How do I know what size sonotube to get?
The rule-of-thumb is to use a tube diameter 3 times the post width, therefore use a 12” diameter Sonotube for a 4×4” post.
How much concrete do I need for a 10 inch sonotube?
For example, a sono tube with a 10″ diameter and a 4′ depth requires 0.08 cubic yards of concrete.
Can I build a house on piers?
Many old houses and small buildings use pier foundations. A pier foundation is an excellent way to reduce the overall cost of your home. If you don’t require the basement or crawlspace provided by a continuous foundation, a pier foundation can solidly support your house while drastically reducing your materials cost.
Is pier and beam better than slab?
While pier & beam systems do create very stable foundations, and are preferable in some situations, they can deteriorate over time. However, they are usually easier and less expensive to repair than a slab foundation. It’s also easier to install, repair and add plumbing with this kind of system.
Are wood foundations bad?
There are two big issues with wood foundations: 1- Any moisture source will lead to premature deterioration. So if the waterproofing isn’t PERFECT, you’re gonna have a bad time. If the basement is finished with an air barrier, eventually you’ll get moisture trapped in the wall cavity, and you’re gonna have a bad time.
How much does it cost to jack up a deck?
On average, deck removal costs between $5 and $10 per square foot depending on the size and condition of the deck. If you have a multi-level, built-in seating, or railing, removal prices will increase. An average 12×12 deck that consists of 144 square feet costs between $720 and $1,440 to remove.
Should a deck be level or sloped?
Most contractors suggest sloping the deck 1/4th- 1/8th of an inch for every foot of decking. With this slope, the difference isn’t terribly noticeable to those standing on the surface but your chance of ponding is reduced greatly.
Can you jack up a deck?
Place them perpendicular to the joists so that you can then raise the whole deck at once as necessary. Place the jacks using the same spacing as any posts or supports. You can use any hand-crank jack for decks close to the ground, such as those included in vehicles for changing tires, or joist jacks for higher decks.
Should I repair or replace my deck?
When the cost of repairs starts to get close to the cost of replacing the entire deck, you should consider replacing the whole thing. Even decking materials that are structurally sound are still old, and you may have to replace them anyway in just a few years.
How much does it cost to replace a wooden deck?
Rebuilding the Whole Deck: If the deck is old or decrepit, removal costs $5 to $15 per square foot, so taking down a 10 x 12-foot deck would set you back about $1,200. A new wood deck costs an average of $14,360, according to Remodeling magazine, and a new composite deck is over 5 grand more at $19,856.
What can you do with old treated wood?
4 Answers
- State statute prohibits open burning of treated lumber.
- Treated wood of all types can be most responsibly disposed of as follows: Homeowners engaged in small projects should take treated wood to their local landfill or transfer station and place it in the designated location (i.e., the non-clean wood pile).
Can you burn old treated wood?
Don’t burn any type of treated wood. Old decks were often built of pressure treated wood, which contains arsenic and chromium. Never burn treated wood. Toxic chemicals will be emitted in the smoke, and ashes from treated wood can be hazardous to livestock or wildlife.
Can you burn rotted pressure treated wood?
Burning this wood can cause exposure to toxic ash and smoke that is harmful to both people and the environment. Incineration of treated wood does not destroy the arsenic and other chemicals it contains. Pressure treated lumber is considered hazardous waste by the U.S. Environmental Protection Agency.
Can you throw away pressure treated wood?
Treated wood of all types can be most responsibly disposed of as follows: Homeowners engaged in small projects should take treated wood to their local landfill or transfer station and place it in the designated location (i.e., the non-clean wood pile).