What does it mean when a VTM-4 light comes on?

When this indicator is on, one or more of your tires is significantly under inflated. You should stop and check your tires as soon as possible. The VTM-4 Lock will temporarily disengage when the vehicle speed exceeds 18 mph (30 km/h). The indicator in the button will remain on.

What does VTM-4 on a Honda Pilot mean?

Variable Torque Management 4WD System

How do you turn off the VTM-4 on a 2006 Honda Pilot?

The first way is simply press the VTM4 button that is located on the dash next to the radio. The second way is to shift the drive selector lever to park and then back to drive while You are stopped. The third way is to turn off the vehicle and then turn it back on.

How do you use the VTM-4 on a Honda Pilot?

If you become stuck, you can activate the VTM-4 by pressing the VTM-4 LOCK button while in first (1), second (2), or reverse (R) gear below 18 mph (30 km/h). This mode overrides the auto system to send maximum torque to the rear axle.

How does the VTM-4 Work?

The VTM-4 Lock® feature allows you to manually lock the rear differential in place to get you moving when faced with extreme conditions. By simply pushing the Lock button, you can fully engage four-wheel drive to gain momentum, putting all of your power to the rear axle.

What does the VSA light mean on a Honda Pilot?

System Indicator Light

How do I turn my VSA light off?

To turn the system off, simply locate the VSA Off button. You’ll find it on the dash, to the left of the steering wheel. Press and hold this button until your hear a beep. The system will turn off, and the VSA Off light will turn on in the dash.

How do you reset the check engine light on a Honda Pilot?

Turn the ignition key to the “II” position and wait for the light to stop flashing on the reset tool. This will reset the electronic control unit, or ECU, and turn the check engine light off.

Why is my check engine light off but code still there?

If you’ve fixed the problem but haven’t cleared the codes with a scan tool, your check engine light will be off but the code will remain stored for a predetermined period of time until (in most cases) it will clear itself.

Is it illegal to disconnect check engine light?

It’s called fraudulent concealment and it is illegal. Many states will allow punitive damages. This car dealership should count themselves lucky that you discovered this problem before it caused any personal injuries.

How far do you have to drive to reset the check engine light?

To make sure the check engine light does not reappear, it’s recommended that you drive your car 30 to 100 miles. This enables the vehicle’s “Drive Cycle” to reset, as the various sensors need time to recalibrate.

How can I tell if my check engine light has been reset?

If the MIL (yellow engine icon) turns off abruptly after 20 seconds, then you know the DTCs have been reset by the engine monitoring system and not by a scan tool or by disconnecting the battery.

What does clearing fault codes do?

On clearing the codes with the “Erase Codes” function, the system status changes to “Not Ready”. Take several individual trips until the system reads the status of all the components once more. “Several trips” means you shut off the engine and start another trip each time.

Is it OK to clear engine codes?

If your main reason for buying an inexpensive scanner is to reset the check-engine light, know this: clearing the code and turning the light off doesn’t mean your issue has gone away. Some check-engine light warnings are temporary—like the aforementioned loose fuel-filler cap or a rare engine misfire.

Can you clear fault codes?

Yes, you can clear the codes without using a scanner. In fact, the check engine light will turn back on in a matter of seconds if the problem still persists. Clearing the CEL is easy… fixing the cause of the problem is the tricky part!

Does disconnecting battery clear codes?

The best way to do this would be with a scanner, but if you don’t have one, disconnecting the battery will do the trick on many vehicles. However, disconnecting the battery will not only erase diagnostic trouble codes but also erase drivability, security and radio codes in many vehicles.

Can Oreillys clear codes?

If your Check Engine Light is on, our Professional Parts People will scan the code for you and provide a list of possible fixes. Some codes may call for further diagnosis.

Can you reset check engine light without disconnecting battery?

Can you reset the check engine light without disconnecting the battery? You can reset the check engine light without disconnecting the battery by using an OBD2 scanner. If you drive long enough after fixing the problem, most car models’ check engine light will go away by itself.

Will disconnecting battery reset abs light?

Resetting Your ABS Dashboard Warning Light Step One: Disconnect the positive cable from your car battery. Then, hold down the brake pedal to drain the vehicle’s electrical system. This will result in a reset of the car’s central computer. If there’s no remaining problem with the system, this should reset the light.

Will disconnecting battery reset car computer?

Will Disconnecting a Car Battery Reset The Computer? The answer is, maybe. Disconnecting the battery for a short time may not do the trick because the car’s computer, or ECU, still has some current in it. Waiting for over 15 minutes after disconnecting the engine will help ensure the equipment is reset.