What are the common types of caught in and caught between hazards?
What are the common types of caught in and caught between hazards?
According to OSHA, caught-in or – between hazards are defined as: Injuries resulting from a person being squeezed, caught, crushed, pinched, or compressed between two or more objects, or between parts of an object.
Which is not a safe rule for power tools?
Never carry a tool by the cord or hose. Never yank the cord or the hose to disconnect it from the receptacle. Keep cords and hoses away from heat, oil, and sharp edges. Disconnect tools when not using them; before servicing and cleaning them; and when changing accessories such as blades, bits, and cutters.
What are the five most basic safety rules for working with tools?
A power tool is a tool that is actuated by an additional power source and mechanism other than the solely manual labor used with hand tools. The most common types of power tools use electric motors. Power tools are classified as either stationary or portable, where portable means hand-held.
What are incompliant tools?
Incompliant tools: must be identified as unsafe, rendered inoperable or physically removed from job sites. Two employer responsiblities listed in this section are instructing employees in recognizing and avoiding unsafe conditions and training employees in the regulations that apply to his or her work environment.
What is Tool safety?
Ensure that employees are properly trained in the safe use of hand tools. Replace or repair defective tools. Keep cutting tools sharp and cover sharp edges with a suitable covering to protect the tool and to prevent injuries from unintended contact.
What are the different types of hand tools?
Categories of hand tools include wrenches, pliers, cutters, files, striking tools, struck or hammered tools, screwdrivers, vises, clamps, snips, saws, drills and knives. Outdoor tools such as garden forks, pruning shears, and rakes are additional forms of hand tools. Portable power tools are not hand tools.
When not in use hand held power tools should be?
Hand-held electric power tools should always be disconnected when not in use to prevent shock or fire hazards.
How do you maintain hand tools?
Clean, Inspect and Care for Tools. Make it a habit to clean tools after each use before you return them to storage. Wipe them down with a rag or old towel and be sure they are free of dust, grease and debris before you put them into their proper places. This is also an opportunity to look for any damage or defects.
What are common hazards when working with Sanders?
The dust created when sanding can be a fire and explosion hazard. Proper ventilation is essential. Do not exert excessive pressure on a moving sander. The weight of the sander supplies adequate pressure for the job.
Which hand held power tools must be equipped with a constant pressure switch?
Other hand-held powered tools such as circular saws having a blade diameter greater than 2 inches, chain saws, and percussion tools without positive accessory holding means must be equipped with a constant pressure switch that will shut off the power when the pressure is released.
Why should you avoid using tools with handles that are too short?
Length. A handle that is too short can cause unnecessary compression in the middle of the palm. It should extend across the entire breadth of the palm. Tool handles should be not less than 100 mm (4 in) to reduce the negative effects of any compression exerted.
Which hand held power tools may only be equipped with a positive on off control switch?
The following hand-held powered tools may be equipped with only a positive “on-off” control switch: platen sanders, disc sanders with discs 2 inches or less in diameter; grinders with wheels 2 inches or less in diameter; routers, planers, laminate trimmers, nibblers, shears, scroll saws and jigsaws with blade shanks
What is the most common injury caused by working with machines unsafely?
Moving machine parts have the potential to cause severe workplace injuries, such as crushed fingers or hands, amputations, burns, or blindness. Safeguards are essential for protecting workers from these preventable injuries.
When a body part is entangled in machinery the spot on the machine where the body part is caught is called?
The correct answer would be option B, Pinch Point. When a body part is entangled in machinery, the spot on the machine where the body part is caught is called the Pinch Point.