What are some wrestling terms?

What are some wrestling terms?

Understanding Wrestling Terminology: A Casual Fan’s Guide

  • Angle: Another term for storyline.
  • Babyface (“Face” for short): The good guy.
  • Blowoff: The last match of a feud.
  • Buried or burial: When a wrestler’s stock begins to fall by having him consistently lose matches or placed in bad storylines.
  • Bump: The act of a wrestler hitting the ground or mat.

What does mark out mean in wrestling?

Dark Match – A match that takes place either before or after a televised show. Feud – A drawn-out rivalry between two or more wrestlers. Mark – Someone who idolizes a particular wrestler, often to the point of excessiveness; the most used term on BR I think.

What does powder mean in wrestling?

to To injure a wrestler by hitting him on the head or causing him to hit his head on something. He is legitimately hurt from the move. Powder out. to To powder out means either you get knocked out of the ring and leave, or you run out of the ring.

What are marking out tools?

Marking Out Tools. Marking Out Tools are important when creating a template or transferring a pattern or design onto a specific workpiece, and are used in many types of construction jobs, joinery, and engineering.

What are examples of marking tools?

Ultimate guide to marking tools

  • Tailor’s chalk. These triangles have been a staple in the tailoring industry for a long time.
  • Chalk cartridge pen.
  • Chalk pencils.
  • Tailor’s beeswax aka wax crayon.
  • Air-erasable pens (AKA disappearing ink)
  • Chaco liner pens.
  • Carbon paper and tracing wheel.
  • Tailor’s tacks or thread basting.

What’s a scriber?

: a sharp-pointed tool for making marks and especially for marking off material (such as wood or metal) to be cut.

What are boring tools?

: a boring bit with its supporting boring bar and arbor, used to enlarge and accurately finish a large bore previously formed by casting or otherwise.

What does countersinking mean?

countersink(noun) a hole (usually in wood) with the top part enlarged so that a screw or bolt will fit into it and lie below the surface. counterbore, countersink, countersink bit(verb) a bit for enlarging the upper part of a hole.

What tool is used to drill holes?

A hole may be drilled or bored; awls, gimlets, and augers also produce holes. An awl is the simplest hole maker, for, like a needle, it simply pushes material to one side without removing it. Drills, gimlets, and augers, however, have cutting edges that detach material to leave a hole.

What is the principle of boring?

In machining, boring is the process of enlarging a hole that has already been drilled (or cast) by means of a single-point cutting tool (or of a boring head containing several such tools), such as in boring a gun barrel or an engine cylinder. Lineboring (line boring, line-boring) implies the former.

What is the reaming process?

Finally, reaming is a cutting process that involves the use of a rotary cutting tool to create smooth interior walls in an existing hole in a workpiece. The rotary cutting tool used in reaming is known as a reamer. Like drill bits, reamers also remove material from the workpiece on which they are used.

What’s the meaning of boring?

boring Add to list Share. As an adjective boring describes something (or someone) that is tedious, dull, and lacking in interest. As a noun, boring refers to the act of drilling a hole, or the hole itself.

Why boring is done?

The goal of boring is to enlarge an existing hole, create a tapered hole from an existing hole, or achieve a desired surface finish inside an existing hole. Boring can be done on lathes, milling machines, or machining centers. There are also specialized machines for boring, such as boring mills or jig borers.

What is reaming used for?

Reamer, rotary cutting tool of cylindrical or conical shape used for enlarging and finishing to accurate dimensions holes that have been drilled, bored, or cored.

What is reaming drilling?

Drilling is performed to originate a hole on a solid surface. Reaming is performed to finish internal surface of an existing hole. So reaming is performed only after drilling (or boring). Cutting tool used in drilling operation is called Drill.

What is a boring test?

As used by foundation engineers, the act or process of sinking holes into the overburden (sometimes to considerable depth into bedrock) with rotary or drive sampling equipment for the purpose of recovering samples from which information on the physical characteristics of the materials penetrated can be obtained; also …

What does auger refusal mean?

Auger refusal shall be defined as auger penetration of less than 6 inches under 500 psi of auger-feed down pressure for a period not less than 10 minutes. Rock coring should not begin or end in weathered shale, weathered limestone, etc., unless absolutely necessary.

How many types of boring are there?

4 Types of Boring Techniques Used During Construction. Boring involves the drilling of holes into the ground for many different purposes. In the construction industry, boring is a technique used to explore the underground surface and to determine if it is capable of holding up a building.

What is N value SPT?

The purpose of conducting SPT is to obtain the standard penetration resistance, commonly called the N value, which is the recorded blow count needed to advance through a 150 mm interval of soil.

What is the purpose of SPT?

The standard penetration test, commonly known as ‘SPT’, was developed to provide geotechnical engineering properties for foundation design purposes. The test is carried out within a borehole. The results can be used to determine the relative density, bearing capacity, and settlement of granular soil.

What is SPT N60?

The standardization compensates for the variability of the efficiencies of different SPT hammer types, and improves the reliability of soil strength estimates used in geotechnical applications. N60 is what a safety hammer (cathead and rope) N value is estimated to be uncorrected.

What is a Shelby tube used for?

Shelby tubes are thin-walled, hollow steel tubes, which are driven into the ground to extract a relatively undisturbed soil sample for use in laboratory tests used to determine density, permeability, compressibility and strength.

How do you collect a Shelby tube sample?

Shelby tube samples are typically collected by advancing a 3.0-inch O.D. seamless steel tube (constructed from either 16-gauge or 18-gauge steel) past the bottom of the advancing drill stem by applying constant downward pressure directly to the drill rod stem using the vertical hydraulic feed system of the drill rig.

How does a split spoon sampler work?

The split spoon sampler is a tube split into two equal halves lengthwise. The two halves are locked together during the sampling activities and released to retrieve the samples. At bottom end of the sampler sits a driving shoe. This is what cuts into the soil and provides the sample that goes up into the tube.

How do you get undisturbed soil samples?

How to Collect Undisturbed Soil Samples. Engineers use drill rigs to collect undisturbed soil samples at depth. Common sampling tools include long split-spoon samplers, piston samplers and a pitcher barrel sampler. Piston samplers are thin-walled tube samplers that collect undisturbed samples in soft soil.

What are the types of soil samples?

There are 2 types of soil sample • Disturbed sample • Undisturbed sample • Disturbed sample :- Natural structure of the soil gets modified or destroyed during the sampling operation. These are also called representative samples. Non-representative samples are those in which soils from other layers get mixed up.

What is considered undisturbed soil?

Undisturbed ground is soil that has been in place since the last glaciation. Once altered by human intervention, it is disturbed (just ask Gaia 😉 You have two options: * dig a test pit to investigate the soil conditions and design accordingly.

What is disturbed and undisturbed soil samples?

If the in-situ properties of soil do not retain while collection process then that type of soil is called a disturbed soil sample. Definition of undisturbed soil sample: When the structural integrity of the soil is retained and has a high recovery rate, then that type of sample is called an undisturbed soil sample.