What is DensShield drywall?
What is DensShield drywall?
Engineered to prevent damage to the sub-floor or wall cavity if moisture seeps through grouted tile, DensShield® Tile Backer is the first backer board with a built-in moisture barrier. Easier to handle than cement board, DensShield Tile Backer cuts and installs like drywall without special tools or fasteners.
How do you seal DensShield seams?
By caulking the intersecting corners of DensShield Tile Backer panels and around a tub base or shower pan with flexible sealant, a moisture-resistant envelope can be established. The sealant should be applied to the DensShield Tile Backer corners PRIOR to taping the joints.
Can you put backer board over drywall?
Because cement board can be used either for floors or walls, the surface below the cement board will vary: In such wet areas, never install cement board directly over drywall or green board. Instead, first, remove the existing surface material, then install the cement board over the studs and membrane, as applicable.
What is DensShield made of?
DensShield Tile Backer is composed of a water-resistant treated core that is covered front and back with fiberglass mats. The mats are permanently integrated with the core during manufacturing, preventing delamination problems that can occur with paper- faced greenboard.
Does Home Depot carry DensShield?
DensShield Gypsum Backer Board 1/2 in. x 2.7 ft. x 5 ft. Tile Backer-008590 – The Home Depot.
Can Densshield be painted?
The nontiled areas can be primed and painted with the same finish used on the other walls in the room as long as the primer and paint are suitable for high-moisture areas.
How much does Densglass cost?
Sign In
| Everyday Low Price | $21.99 |
|---|---|
| 11% Mail-In Rebate Good Through 4/17/21 | $2.42 |
Is DensGlass a drywall?
DensGlass 5/8-in x 4-ft x 8-ft Mold Resistant Moisture Resistant Fire Resistant Drywall Panel.
Can DensGlass be used in a shower?
The densglass is used in place of normal gypsum sheathing and is installed against the exterior framing prior to the tub / shower installation. DensShield Tile Backer can be installed in the shower pan if part of an approved system.
Is DensGlass waterproof?
It is a ready-mixed, flexible, waterproof coating which can be used on gypsum, cement or wood based sheathing substrates. Sto VaporSeal over DensGlass panels can be used on vertical above grade walls.
Does Densshield require waterproofing?
Densshield, with its gypsum core and waterproof surface, requires waterproofing at the edges where the gypsum is exposed and at any penetrations of the waterproof surface.
Can you finish DensGlass?
Can you finish DensGlass? Panels are applied directly to structural framing. Surface and joints may be finished and painted, or surfaced with an exterior finish system. DensGlass Sheathing is resistant to normal weather conditions, but it is not intended for immersion in water.
Can you screw into DensGlass?
DensGlass Sheathing can be attached parallel or perpendicular to wood or metal framing. Nails or screws, as listed in the fastener chart, may be used to attach DensGlass Sheathing to framing.
What is DensElement?
The DensElement Barrier System is a gypsum sheathing, water resistive barrier, and air barrier system when the joints, fasteners, penetrations, openings, and transitions are properly sealed with an approved third party fluid-applied flashing.
How do you cut DensGlass?
The nice thing about this product is you can cut it with a utility knife just like using regular drywall.
Who makes DensGlass?
Dens Solutions carry the mark of our valued heritage in Gold, as a visible standard-bearer of our position as the first manufacturer to create a fiberglass mat board and as a relentless innovator of strength and moisture resistant products for over 30 years.
What can I use for exterior sheathing?
Five common structural exterior sheathing options include wood-based, gypsum, glass mat, cement board, and Barricade® Thermo-Brace®. Plywood sheathing is made from whole sheets of wood that are cross-laminated, which give the boards strength and stiffness. This helps with expansion and contraction.
What is glass mat gypsum?
A water-resistant, gypsum tile backer with embedded glass mats and a textured coated surface for tile applications. The lightweight 1/2″ thick product is a superior tile substrate for walls, ceilings and countertops.
What is exterior gypsum board?
Exterior Gypsum Sheathing is a special-purpose drywall panel consisting of a moisture-resistant, noncombustible core covered by glass-mat facers on both front and back surfaces and long edges. Gypsum Sheathing is well established as a cost-efficient exterior substrate in commercial construction.
Can gypsum board get wet?
Gypsum board may experience limited intermittent exposure to moisture from a variety of sources, such as improper storage, construction or design defects, water leaks, and janitorial activities. Gypsum board exposed to water should be replaced unless all of the following conditions are met.
What thickness drywall is used for ceilings?
5/8-inch
Which is better sheetrock or drywall?
Drywall and sheetrock are really the same thing. Sheetrock is a brand of drywall patented by the US Gypsum Company. Both are used to make walls and ceilings. Aside from a few chemicals that allow the sheetrock formula to be patented, there is really no practical difference between drywall and sheetrock whatsoever.
What is the best drywall for ceilings?
The thicker ⅝” drywall is the standard for ceilings. You don’t want to use ½” or ⅜” for ceilings, as over time it will sag downwards in between rafters. Also, ⅝” is the standard thickness for fire-resistant or fire-code drywall, commonly found in garages.
Is lightweight drywall good for ceilings?
There is no appreciable design advantage for ultralight drywall over standard drywall. This is a material that can be used for all wall and ceiling finish surfaces in any residential application.
Which is cheaper plaster or drywall?
When building a new house, real plaster walls are more expensive than drywall. But in an old home that already contains plaster, it is almost always more cost effective — and more attractive — for the homeowner to keep the plaster than replace it.