Users questions 

What does check AquaPure general fault mean?

Joe Ford

What does check AquaPure general fault mean?

Posted July 14, 2009. The unit is reporting that your Chlorine generator has a problem and needs your attention. You will need to go out to the pool equipment and wait for the Aqua Pure to display a 3 digit code, This code will direct you to the problem.

How do I reset my Jandy AquaPure?

Each time a flow sensor is unplugged and plugged back in again the computer inside the unit must be reset by turning the power ‘off’ and then ‘on’.

What does cell reversing mean on AquaPure?

AquaPure automatically cleans the Cell electrodes once every 3 hours by reversing polarity. This does not interrupt the production of Chlorine.

How do you clean AquaPure cells?

Add one pint of muriatic acid to two quarts of water in a bucket. Pour the solution into the cell so it begins to foam. Leave the solution in the cell until the foaming has stopped or until the solution has been in the cell for more than 30 minutes.

How do you calibrate a Jandy salt sensor?

Press the “Salinity”button and hold it until it beeps 3 times. The system will beep when you push it and then at 5 seconds and again at 10 seconds. Release the button after the 3rdbeep. Press and release the “Temperature “button within 5 seconds to enter the salinity calibration screen….

How do I calibrate my Aqualink?

How to calibrate the temperature on your iAqualink Unit

  1. Click on the “Pool” button.
  2. Adjust the temperature using the arrow keys.
  3. Click the “Back” button until you reach the home screen again.

How do you clean a Jandy 1400 Salt Cell?

How to Clean a Jandy AquaPure Water Purification System

  1. Remove the cell from the Jandy AquaPure Purification System.
  2. Remove the sensor from its port on the cell if scaling is detected.
  3. Wash the cell well with water.
  4. Turn the flow/temp/salinity sensor counterclockwise to remove it from the three-port cell.

How do you calibrate a pool thermometer?

  1. HOW TO CALIBRATE. A THERMOMETER.
  2. Fill a large container with crushed ice. Add clean tap water until the container is full. Stir the mixture well.
  3. Thermometers should be calibrated regularly to make sure the readings are correct. The ice-point method is the most widely used method to calibrate a thermometer.
Common questions 

What does check AquaPure general fault mean?

Joe Ford

What does check AquaPure general fault mean?

Posted July 14, 2009. The unit is reporting that your Chlorine generator has a problem and needs your attention. You will need to go out to the pool equipment and wait for the Aqua Pure to display a 3 digit code, This code will direct you to the problem.

Why does AquaPure say no flow?

I would like to remind everyone that if your AquaPure system is showing “No Flow”, with or without any other error codes, your system IS NOT making chlorine. Don’t ignore it.

What does cell reversing mean on AquaPure?

AquaPure automatically cleans the Cell electrodes once every 3 hours by reversing polarity. This does not interrupt the production of Chlorine.

What percentage should my chlorinator be at?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

How do you recalibrate Jandy salt?

Press the “Salinity”button and hold it until it beeps 3 times. The system will beep when you push it and then at 5 seconds and again at 10 seconds. Release the button after the 3rdbeep. Press and release the “Temperature “button within 5 seconds to enter the salinity calibration screen.

How do I know if my flow switch is bad?

If the flow switch is stuck closed, when you unplug the wire inside the controller, the producing-chlorine light should go off. If the light does not go off, then the problem should be inside the controller.

How do you read a Jandy serial number?

The serial# is on a white tag on the bottom of the power supply. For example, serial number CM3 86 can be read as follows: CM3 means it is a ClorMatic III, 01 is the year, 06 is the month, 13 is the day and 86 is the unit manufactured that day.

How do you remove a Jandy AquaPure salt cell?

Add one pint of muriatic acid to two quarts of water in a bucket. Pour the solution into the cell so it begins to foam. Leave the solution in the cell until the foaming has stopped or until the solution has been in the cell for more than 30 minutes.

What should my Intellichlor be set at?

What should the salt level be? The intellichlor is set to function when the salt level is between 2800 ppm and 4500 ppm. Too little, it cannot make chlorine. Too much salt and it also cannot (should not) make chlorine and can cause additional voltage issues with your pool and equipment.

What should the salt level be in a pool?

between 2700-3400 ppm
The ideal salt level is between 2700-3400 ppm (parts per million) with 3200 ppm being optimal. Before adding salt to your pool, test the water to check your salt level. If the level is low, determine the number of gallons in the pool and add salt according to the chart below.

How long does a Jandy salt cell last?

3-5 years
It’s important to note, properly maintained salt cell will last 3-5 years; an improperly maintained cell can fail in a year. Considering that salt cells are relatively expensive, we want to make sure you know the basics about prolonging their lifespan so you’ll get the most value for your dollar.

How do you bypass a flow switch?

How to Bypass a Flow Sensor in a Pool Heater

  1. Shut off the circuit breaker that controls electricity to the pool heater and the pool pump that sends water through the heater.
  2. Use a screwdriver to take out the screws holding the housing over the heater.
  3. Detach the two wires from the sensor.

How do you test a flow switch?

How to Test a Flow Switch

  1. Put cover on the flow switch and turn power on.
  2. Start flow through the designated system.
  3. Observe flow in operation to determine if flow switch is working properly.
  4. Repeat this process many times to ensure flow switch and designated system is in fact working accurately. Tip.

Is Jandy and Zodiac the same company?

Zodiac Pool Systems, Inc., a subsidiary of Zodiac Marine & Pool, S.A.S., is a global leader in swimming pool and spa products and services. The company’s comprehensive product lines are marketed under the leading brand names of Zodiac®, Polaris®, Jandy Pro Series®, Baracuda®, Nature2®, and Cover-Pools®.

Who owns Jandy pool?

Jandy Pool Products is a developer, manufacturer and marketer of innovative pool products sold under the Jandy® brand. Jandy was acquired by Carlyle (80%) and the Zodiac Group (20%) in April 2006.

Lifehacks 

What does check AquaPure general fault mean?

Joe Ford

What does check AquaPure general fault mean?

Posted July 14, 2009. The unit is reporting that your Chlorine generator has a problem and needs your attention. You will need to go out to the pool equipment and wait for the Aqua Pure to display a 3 digit code, This code will direct you to the problem.

How do I reset my AquaPure?

Each time a flow sensor is unplugged and plugged back in again the computer inside the unit must be reset by turning the power ‘off’ and then ‘on’. Failure to do this will result in erroneous readings. within 5 seconds to store it in memory.

How do you turn off Jandy AquaPure?

Press the salinity button and hold it for 5 seconds. The unit will beep when it is pressed and then again after 5 seconds, this will silence the alarm for 24 hours or until the unit is turned off and on again. Turn the AquaPure off by pressing the A (down arrow) and setting CHLORINE PRODUCTION to 00%.

How do you clean AquaPure cells?

Add one pint of muriatic acid to two quarts of water in a bucket. Pour the solution into the cell so it begins to foam. Leave the solution in the cell until the foaming has stopped or until the solution has been in the cell for more than 30 minutes.

What does a service code on a Jandy aquapure mean?

If you have a Jandy AquaPure 700 or 1400 chlorinator, there’s a chance you may have come across a service code (or error code) before. A service code is a three digit number that appears on the display panel of an AquaPure Control Box, letting you know if your AquaPure unit is experiencing any problems.

What to do if your Jandy pool sensor is not working?

Jandy recommends that you contact a pool professional for service if you encounter a Level 2 code. Heated sensor element not heating. (Generates 172 code) Contact a pool professional. Flow sensor temperature sensor failure. (Generates 172 code – flow sensor service)

Where to get help with aquapure error codes?

If you need more help understanding the AquaPure Error Codes, or need help fixing the issue, stop by a local Leslie’s Pool Supplies store and speak with a trained pool professional today. You can also request pool equipment and repair services by contacting our Pool Service and Repair Department HERE.

What does Aqualink Rs do on Jandy aquapure?

AquaLink RS is controlling the AquaPure and desired output percentages. AquaLink RS is controlling the AquaPure and “Boost” is active. If you need more help understanding the AquaPure Error Codes, or need help fixing the issue, stop by a local Leslie’s Pool Supplies store and speak with a trained pool professional today.